-
1 прочность клеевого соединения при сдвиге
прочность клеевого соединения при сдвиге
прочность при сдвиге
Разрушающее напряжение клеевого соединения внахлест при приложении усилия под углом 180° к плоскости клеевого шва и приведенное к площади.
Примечание
Термин распространяется на клеевые соединения встык при кручении.
[ ГОСТ 28780-90]Тематики
Обобщающие термины
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > прочность клеевого соединения при сдвиге
См. также в других словарях:
Strength of materials — Internal force lines are denser near the hole, a common stress concentration In materials science, the strength of a material is its ability to withstand an applied stress without failure. The applied stress may be tensile, compressive, or shear … Wikipedia
Tsai-Wu failure criterion — The Tsai Wu failure criterion [Tsai, S. W. and Wu, E. M. (1971). A general theory of strength for anisotropic materials. Journal of Composite Materials. vol. 5, pp. 58 80.] is a phenomenological failure theory which is widely used for anisotropic … Wikipedia
прочность клеевого соединения при сдвиге — прочность при сдвиге Разрушающее напряжение клеевого соединения внахлест при приложении усилия под углом 180° к плоскости клеевого шва и приведенное к площади. Примечание Термин распространяется на клеевые соединения встык при кручении. [ГОСТ … Справочник технического переводчика
solids, mechanics of — ▪ physics Introduction science concerned with the stressing (stress), deformation (deformation and flow), and failure of solid materials and structures. What, then, is a solid? Any material, fluid or solid, can support normal forces.… … Universalium
Micro-Mechanics of Failure — Figure 1. Hierarchy of micromechanics based analysis procedure for composite structures. Micro Mechanics of Failure (MMF) is a newly proposed methodology, providing a more logical explanation of failure mechanism of continuous f … Wikipedia
Screw — This article is about the fastener. For other uses, see Screw (disambiguation). Screws come in a variety of shapes and sizes for different purposes. U.S. quarter coin (diameter 24 mm) shown for scale. A screw, or bolt, is a type of fastener… … Wikipedia
Reinforced concrete — is concrete in which reinforcement bars ( rebars ), reinforcement grids, plates or fibers have been incorporated to strengthen the concrete in tension. It was invented by French gardener Joseph Monier in 1849 and patented in 1867.[1] The term… … Wikipedia
ГОСТ 23431-79: Древесина. Строение и физико-механические свойства. Термины и определения — Терминология ГОСТ 23431 79: Древесина. Строение и физико механические свойства. Термины и определения оригинал документа: 31. Абсолютно сухая древесина E. Oven dry wood F. Bois sec absolu Древесина, высушенная до постоянной массы при температуре… … Словарь-справочник терминов нормативно-технической документации
Earthquake — For other uses, see Earthquake (disambiguation). Global earthquake epicenters, 1963–1998 … Wikipedia
Bending — For other uses, see Bending (disambiguation). Flexure redirects here. For joints that bend, see living hinge. For bearings that operate by bending, see flexure bearing. Continuum mechanics … Wikipedia
glacial landform — ▪ geology Introduction any product of flowing ice and meltwater. Such landforms are being produced today in glaciated areas, such as Greenland, Antarctica, and many of the world s higher mountain ranges. In addition, large expansions of present… … Universalium